****1. STANDBY LEDRed light is emitted when the product is in standby mode.**2. STANDBY BUTTONSwitches between operation and standby modes.**3. VOL BU
****1. STANDBY LEDRed light is emitted when the product is in standby mode.**2. TV LEDGreen light is emitted when the product is in TV mode.**3. RADIO
****1. STANDBY LEDRed light is emitted when the product is in standby mode.**2. STANDBY BUTTONSwitches between operation and standby modes.**3. VOL BU
) %**1. LNB INConnects a satellite antenna cable.**2. LNB OUTConnects another digital satellite receiver.**3. RS-232CConnects to the PC to
)* %1. SOURCECurrently not supported**2. TV/RADIOSwitches between TV and radio modes.**3. NUMERIC(0-9) BUTTONSEnters a TV/radio channel
**14.STANDBYSwitches between operation and standby modes.**15.GUIDEDisplays the standard EPG.**16.EXITCloses and returns to the previous menu.**17.OKS
!+**You can connect the product to the TV with the particular equipments for gaining optimum signalquality. The product provides various interfa
,%% - **When powering on your product for the first time after purchase, the installation wizard will operateautomatically. .!
2* You can set the current time.Select Current Time/Time Offset/Daylight-Saving Timeand set an option.Note: Set the current time to recei
% .**You can display the channel list and switch to other channels.Five types of channel lists are provided for quick and easy channel sea
**Thank you for purchasing a HUMAX product. Please read this user’s manual carefully to be able tosafely install, use and maintain the product at maxi
*+%31 4 % .1. Press the OK button while viewing a programme todisplay the channel list. You can also display thechannel list by s
26 ! 67 26 ! You can view the detailed programme information of each channel in time and date order. Press theGUIDE button or press
26 ! **You can also customise your own programme guide to list the channels or programmes of interestto you and schedule your viewing usi
% %**You can set rating limits for each programme according to the age of the viewer or change yourprevious PIN-Code.**1. Press the ME
# ,%%**You can configure the installation setting and perform channel search.Tip:• The default PIN-Code is 0000.• The default PIN-Code is 82
# 5 %1. Press the MENU button.2. Select Installation and press the OK button.3. Select Organising Channels and press the OKbutton.Or
**# % 1. Press the MENU button.2. Select Installation and press the OK button.3. Select Channel Search and press the OK button.Humax Aut
# !**1. Press the MENU button.2. Select Installation and press the OK button.3. Select Status and press the OK button.STB StatusYou can confirm
& 7+ In order to maintain proper performance of the product, it is essential to have the most up-to-datesoftware. Visit the Humax webs
& 7 + * You can connect your product to the PC directly and update your software by transferring the newsoftware from the PC. F
**Warnings, Cautions and NotesThroughout the whole manual, pay special attention to the following marks that indicate hazardoussituations.**• WarningI
' 1++ 0' 2!;% Before contacting your local service centre, please read the tips below carefully. If the problempersists aft
4. No or poor sound• Check that your AV cable is connected correctly.• Check the volume levels of your TV set and the product.• Check if the product o
' < =Error message Possible causes What to doNo or bad signal The satellite dish is not pointing atthe satellite.Adjust dish align
' +Tuner & ChannelInput Connector IEC 169-24 female (F-Type)Frequency Range 950MHz to 2150MHzSignal Level -25 to -75 dBmVLNB Po
A/V & Data In/OutVideo 1 Output RCA (CVBS)Audio 2 Output RCA (Audio L/R)RS-232C 9 pin Socket typePower SupplyInput Voltage 90~250V AC, 50/60HzType
' 4 !++Information concerning troubleshooting, software upgrade and product support is provided in thefollowing websites and call
1!%Tel: 1800 613 011Opening Hours: Mon- Fri 9:00-17:30E-mail: [email protected]: www.humaxdigital.com/australiaLanguage: Englis
**This product has been manufactured to comply with international safety standards. Please read thefollowing safety precautions carefully.**Safety Ins
10.LOCATION• Place the product indoors to avoid exposing it to lightning, rain or sun.• Do not place it near a radiator or heat register.• Make sure i
**Warning**The mains plug, as a disconnection device, shall remain readily accessible by the user.**1. To avoid damage of the power cord or plug;• Do
1. Before Using the Product ... GB71.1 Package Contents ...
!This chapter provides detailed instructions on the product and its accessories. " Please check all pac
$ %****1. STANDBY LEDRed light is emitted when the product is in standby mode.**2. STANDBY BUTTONSwitches between operation and standby mo
Kommentare zu diesen Handbüchern